How far Omnet++ and MATLAB will help in MEC research ?

More Antharaju Kalyan Chakravarthy's questions See All

How to define fuel mixture as input in ansys fluent species transport model ?

I want to define a CO + H2 mixture fuel for a combustor. How can I define this in ansys fluent mixture template ? Normal database does not include this mixture . eg. if I want to define a mixture...

01 February 2021 6,860 2 View

Please suggest me present research buzz word in the field of networking..?

I feel very happy to tell you ,I am interested in networking,i would like to continue my research in the field of wireless networks.i need some suggestion regarding where i need to start my...

03 January 2020 7,641 6 View

Hello, I have synthesized a copper complex, with mass 447 and analysed using MALDI , for which I have got mass of 493?

The mass corresponds to complex + formaldehyde or complex +2 Na. Is it possible in MALDI?

16 March 2019 765 5 View

What are the differences and advantages of using .h5 files over .npy files or vice versa?

I have a huge collection of images and I converted them into '.npy' and '.h5' format but the resulting size of folders of h5 and npy files are way more than that of the size of original images....

06 July 2018 7,564 1 View

What are the parameters that can be considered to tune a neural network to improve accuracy?

Apart from increasing the number of epochs , the number of layers in the network . fine tuning my learning rate, how can the accuracy be increased?

01 June 2018 4,391 3 View

Need information about RP-HPLC for peptide purification?

Hi Guys, I need a procedure for using reverse phase semi-preparative RP-HPLC. Generally how much time will it takes to purify 100 mg of small peptides. How much solvent is necessary to prepare the...

24 September 2017 9,251 7 View

What are the possible adaptation measures to be followed in crop production for the future climate (Increased Temperature and Increased CO2)?

For Temperate regions..

28 April 2016 4,808 8 View

Where can I find electropolishing parameters for nickel at room temperature?

Electropolishing of nickel

28 May 2015 7,539 3 View

What is the relationship between variable carrier concentration and 2D electron (hole) gas system?

It is difficult to change the intrinsic carrier concentrations of metals and semimetals and therefore 2D gases in such materials was not discussed. Why?

22 November 2014 2,375 1 View

Workstation configuration for illumina miseq?

Hi, we are working on stool-metagenomics based on V3V4 and ITS2 amplicon sequencing. We would like to analyse data in a work station by using QIIME. Can someone help me with the best configuration...

01 January 1970 4,257 3 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

How to improve and implement WBAN MAC and Radio modules under Castalia 3.2 ?

Hello researchers, Hello Castalia3.2 researchers I am a beginner with Castalia, I work on optimization of RFID systems used in wireless body networks. I simulated a WBAN with 10 nodes and one...

28 February 2021 400 1 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

Is it possible to set a breakpoint at a specific DYNAMIC instruction using the GNU Debugger (GDB)?

Using GDB, it is straightforward to debug and monitor a target program by setting a break-point at a specific instruction, since the instruction addresses are known. However, we have two...

24 February 2021 1,598 2 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View

Should I use Pressure Based Solver or a Density-Based Solver?

Dear researchers, I want to simulate a flow (air) in a wind tunnel, and I want to integrate a fluidic actuator inside it in order to control the separation of the boundary layer. At the blower...

22 February 2021 4,882 3 View

How to simulate 5G Quality of Service characteristics?

For my research, I would like to simulate an end to end 5G network. My goal is to observe the behaviour of SDAP protocol, dynamic configuration of 5QI values etc. To summarize I would like to...

21 February 2021 7,624 3 View

Open Source IoT Simulators supported by Machine Learning?

Dear Research Gaters, Let me first add context to the question. I am looking to simulate the waste management system and resources of a city. The hardware devices I need to simulate include,...

21 February 2021 2,333 4 View

Amit Choksi

A good option would be to explore NetSim plus MATLAB. NetSim can model the network communication while MATLAB can be used to model the compute in MEC. You could also run various ML algorithms in MATLAB or Python.

Antharaju Kalyan Chakravarthy

Thank your dear Amit Choksi for your response.