How do you calculate the efficiency of a group of piles that mainly consists of loose sand?

More George Bekas's questions See All

How can a rigid diaphram be modeled in OpenSees?

Can I model a diaphragm as multiple master-slave node, lines of code or should I specify the whole polygonal boundary at once?

11 December 2017 602 6 View

Is there any notion of effective moment of inertia used in analysis RC elements according to Eurocode 2?

When conducting finite element analysis according to the Eurocodes, is it sufficient to use the uncracked moment of inertia, or is there any notion for the effective moment of inertia alike the...

10 November 2017 5,262 6 View

Can Eurocode 6 be applied for RC walls?

I am searching for a detailed solved example of a shear wall that also have to resist an axial load (design should be compliant to Eurocodes).

10 November 2017 504 4 View

How do I check the structural capacity of an element in OpenSees?

I am trying to find through which combination of commands, I check if a particular cross section, has sufficient capacity or not, after the structural analysis. The structural analysis will...

10 November 2017 5,470 4 View

What are some examples of good conferences about Building Information Modeling?

Especially if it is combined with workshops.

09 October 2017 532 1 View

I am looking for a particular resource about the modeling of the load transfer from slabs to beams in a 3D FE analysis context. Any ideas?

E.g. fixed end moments, shear forces, etc.

09 October 2017 2,055 4 View

Is there an example where recurrent neural networks have been used for optimization purposes?

Would the modeling of a physical system that displays a dynamic behavior be benefited by the use of e.g. genetic algorithms in order for optimal temporal decisions to be determined?

09 October 2017 4,959 3 View

What does this particular MATLAB code mean?

loads{k,1}=loads{k-1,1}+1; loads{k,2}='py';

09 October 2017 3,177 3 View

What is a sufficient sample for a recurrent neural network?

Is there any relevant theory and publications?

09 October 2017 6,155 3 View

What is recource for the load distribution coefficients for one way and two way slabs according to the Pieper/Martens method?

E.g. tables etc.

09 October 2017 8,099 3 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,492 1 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,545 2 View

May I know the exact Quartile of the journal- Advanced Engineering Materials (Wiley) for material science category?

In some data sources it has been grouped in Q1 and some shows it is Q2.

29 July 2024 4,226 2 View

What should a Mechanical Engineering PhD scholar focus on during their PhD to enhance their chances of securing a postdoctoral position?

29 July 2024 7,713 4 View

Ternary in Electrical Engineering?

Dear Research Community I would like to invite Elctrical Engineering specialists to solve problems related to Ternary Algebra or tripple sets I have an algorithm that places in relation three...

28 July 2024 5,771 2 View

What topic or subject does Production Engineering need to address more?

Contemporary scores or innovations in scientific approaches. Hybrid methodologies, emerging themes and cross-cutting issues?

27 July 2024 647 3 View

Can a shoot-through event of a tri-state digital buffer cause momentary Hi-Z state?

// interested in the difference between floating events and short circuits.

22 July 2024 6,565 0 View

Is there a good macro photography kit for on-site metallurgical investigation?

I am looking to purchase a photography kit for onsite metallurgical investigations, such as capturing photos of worn areas, hot tears, cold tears etc. Could anyone suggest me a good...

22 July 2024 3,490 2 View

Why do fish have fishy odors naturally ?

Chemical Engineering /Food Engineering

20 July 2024 4,151 4 View