How can I generate lorentzian and gaussian profiles with the same FWHM using Matlab?

More Zuhaib Haider's questions See All

How to estimate the instrumental line width in emission spectroscopy experiment?

How do you estimate the instrumental line width in emission spectroscopy experiments? Do we need calibration lamp of some sort?

09 October 2014 4,244 6 View

Can anyone help me with writing a Matlab code for a convolution of two functions?

I want to write a code for convolution of two functions (e.g., lorentzian and exponential) in Matlab. I am familiar with basics of Matlab, but not familiar with convolution of the functions.

09 October 2014 8,572 6 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

How to prevent ANFIS Model from negative prediction values in MATLAB?

I have input and output data set for "ANFIS modeling in MATLAB", and I am getting some negative predicted values of output in testing. However, the predicted values of output in training are...

28 February 2021 3,459 3 View

How does an AC-DC power supply Flyback Converter Based USB Charger Model using Matlab/Simulink looks like?

I am required to learn about Flyback converters and I got stuck not knowing to full design of the power supply flyback converter Based USB Charger Model using Simulink, especially the design model...

25 February 2021 5,435 2 View

Please. Could you help be in implementing Fractal Discrete Cosine Transform algorithm in Matlab?

I do need the Matlab code of Fractal Discrete Cosine Transform (FDCT). Can anyone who has already implement this code, help me with the implementation of this transform?

24 February 2021 5,602 2 View

D2D implementation in Matlab in Vienna LTE software?

Hi Hope you are well. Can you please share your code for D2D implementation in Matlab. I want to implement D2D in Matlab based Vienna simulator and struggling to deploy D2D. Thanks

24 February 2021 9,378 3 View

Multi effect distillation modeling in EES?

Dear colleagues If anyone has a model of multi-effect distillation in EES or MATLAB software, please send it to me.

24 February 2021 7,282 1 View

What program can I use to caclulate dipole moment efficiently and without the need of excessive computation?

Hi, I am a third year chemistry undergrad doing my group project in which I need to predict the HPLC retention time of 20 aromatic molecules. to do this we require the chemical properties of these...

24 February 2021 1,384 3 View

Does anyone ever solved this following Matlab error : "Error using imaqdevice/start (line 95) pointgrey: Failed to stop the camera acquisition." ?

I use Matlab 2014b to capture some images with a PointGrey camera connected with USB3 port. I initialize the camera in a function which basically execute these followed lines : vid =...

22 February 2021 6,386 1 View

How to build fouling and erosion simulation model for Aero Engine compressor and turbine rotor in Simulink / Matlab?

22 February 2021 3,697 1 View

Juan Gomez-Cruz

I do not Know if it is what you are looking for, but I think that if you have some points, in this case at least you have the two ends of the FWHM and the center, and then you could try making a curve fitting with Gaussian and Lotentzian equations.

I hope this will help you.

Greetings

Zuhaib Haider

I used respective functions and input same values to FWHM variable. It went fine.

Thanks :)