I am working on project that I need to use a USRP2,but when I try to calibrate it,I get the above error(on attached graph) or" time out waiting for TX and/or RX LO to lock".Anyone here knows how to get a rid of this?
Thank you
Tough to say the reason, it could be a number of possibilities.
Heres some questions/stuff you can try:
1) Which LO is failing to lock RX or TX? The logic is in the
tune_rx_and_tx() routine of the .cpp file.
2) Perhaps the timeout is marginal. Does increasing the timeout allow
for lock?
3) Perhaps locking at lower frequencies is marginal. Does increasing the
start frequency --freq_start allow for lock across all frequencies in range?
4) Perhaps there is a hw issue? Does the board work as expected with
simple test tones, transmit and receive. Do you have another device to
cross reference?
best regards
you may attached excel sheet for the plotting of your graph, where your output is coming.
1. Add a excel sheet that extract the data
2. plot using office
I know this my sound a little bit basic but I know spiral antennas either planar or conical were developed by Rumsey,J Dayson,and et al;at the same time Raymond DuHamel and Dwight Isbell were...
05 June 2017 346 3 View
I know this is something easy to do but I am kind of stuck on it.I have antenna with impedance changing with frequency,I have matlab function that will give me a microstrip tapped lines dimensions...
09 October 2016 3,797 5 View
Anyone save me please I know patch antenna dimensions can be calculated easily but how big(width and length) of a substrate have to be?And what about its exciting ports(in case of waveport and...
03 April 2016 4,728 6 View
01 February 2016 637 8 View
Any one knows how I can get design parameters of pyramidal horn antenna?I want to design antenna operating in range of 3.1-10.6GHZ(Medical range) with mid frequency of 7GHZ.I have a =.9 in ,b=1.78...
11 December 2015 6,623 9 View
Excessive rotation of nodes in node set ErrNodeExcessRotation-Step1
17 August 2021 0 0 View
20 June 2021 0 0 View
What this unit identifies for the ion exchange capacity ca. 0.92 meq. g-1. I am a newcomer in the membrane area. I just started. I highly appreciate your help
08 May 2021 0 0 View
--> FOAM FATAL ERROR: Maximum number of iterations exceeded From function Foam::scalar Foam::species::thermo::T(Foam::scalar, Foam::scalar, Foam::scalar, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar, Foam::scalar) const, Foam::scalar (Foam::species::thermo::*)(Foam::scalar) const) const [with Thermo = Foam::hConstThermo >; Type = Foam::sensibleEnthalpy; Foam::scalar = double; Foam::species::thermo = Foam::species::thermo >, Foam::sensibleEnthalpy>] in file /home/ubuntu/OpenFOAM/OpenFOAM-4.1/src/thermophysicalModels/specie/lnInclude/thermoI.H at line 66. FOAM aborting #0 Foam::error::printStack(Foam::Ostream&) at ??:? #1 Foam::error::abort() at ??:? #2 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::calculate() at ??:? #3 Foam::heRhoThermo >, Foam::sensibleEnthalpy> > > >::correct() at ??:? #4 ? at ??:? #5 __libc_start_main in "/lib/x86_64-linux-gnu/libc.so.6" #6 ? at ??:?
24 March 2021 0 0 View
I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...
03 March 2021 4,116 4 View
I looking for ferro calcium production process
03 March 2021 1,755 4 View
Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,
02 March 2021 0 0 View
Which is suitable for use with Python? MySQL or SQL Server? What is your suggestion?
01 March 2021 3,422 3 View