Can I use solid186 with dropped midside node for strenth check of composite ?

04 April 2017 0 2K Report

I got converged result for rebar reinforced concrete with solid186 material for concrete, now can I use it's result to propose failure of concrete by comparing with it's compressible strength of 41MPa?

Badges
Science topic

More Mahesh Patil's questions See All

How to given connection in RBD(rigid body dynamics) for end cover displacement calculation?

Hello all, I am new in simulation of rigid body dynamics problem,the detailed definition of problem is given below: Problem Definition: The aim of this analysis is to find the displacement of end...

08 September 2017 5,926 0 View

CFD analysis of vane groove with reciprocating vane, have to check are vanes tilting towards side plates which causes wear on side plate?

I came across problem of wear on side plates (pressure plate/front plate) of vanes, to detect cause of wear, I need to do CFD analysis of vane groove with moving vane (centrifugally). I have to...

04 May 2017 7,628 0 View

How to use SOLID185 element for simulation of concrete in ANSYS workbench?

I am working on structural analysis of steel reinforced concrete project in ANSYS workbench. which type of elements will be better to simulation of concrete?

03 April 2017 6,912 7 View

What is the procedure to determine the permeability of concrete?

can anyone help me in this, it will help me with my research work

01 March 2021 834 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Apart from Nanosilica and CNT's what are the other nanomaterials readily available to use in concrete mixture?

Nanotechnology in concrete materials

01 March 2021 3,379 3 View

Concrete compressive strength databases?

I am looking for datasets similar to this one: http://archive.ics.uci.edu/ml/datasets/Concrete+Compressive+Strength I am looking for concretes with different types of aggregates (Recycled,...

27 February 2021 6,801 3 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

What is the best way to calculate the angles of twist for concrete columns subjected to torsional moment using finite element software?

In Finite element software like ANSYS , there is difficulty in obtaining direct results of twisting of concrete members because SOLID65 which is the unique element designed to represent concrete...

26 February 2021 3,806 2 View

Compute for the total volume of concrete needed for the concrete pouring of the foundation including its column up to NGL only as shown in the plan?

Looking for the quantity of cement, sand, and gravel of footings and columns. Thank you!

25 February 2021 3,092 2 View

Best FE Program for Concrete Strengthened with FRP Sheets?

Colleagues, I have been using ANSYS to model concrete strengthened FRP sheets, but less than happy with it. Any has recommendation for efficient, easy to use FE program for modelling concrete...

22 February 2021 7,528 3 View

Is there a Constitutive model for concrete with Sea-Sand?

Hi I am running a simulation in Abaqus for a concrete beam. Its fine aggregate replaced with sea-sand. I was wondering if I could find studies that measured the ultimate strain of concrete made...

22 February 2021 6,409 2 View

Which type of loading is to be used in dynamic analysis of Machien foundation?

Hello Everyone, Hope you all are doing well. I'm trying to simulate a machine foundation in ABAQUS with a geo-cell reinforced soil bed. Im totally confused to which type of loading would be...

21 February 2021 4,388 3 View