Bond strength of repair mortar and Old concrete?

Pabasara Rathnaweera @Pabasara_Rathnaweera3

09 September 2017 0 9K Report

Is there any kind of standard experiment test available to check the "Bond strength of the newly added repair mortar and the old concrete" in a concrete structure

Badges
Science topic

More Pabasara Rathnaweera's questions See All

FREE DOWNLOADS OF BS 6349 maritime codes?

Can anyone find BS maritime codes (BS 6349, PART 1-8) FREE DOWNLOADS as PDF. I am currently doing a coastal engineering project and i am in need of those codes for my design works.

07 August 2017 4,811 1 View

Wave modelling by DELFT 3D software

Does anyone know the procedure of Wave modeling to a given bathymetry by DELFT 3D wave modeling software. My project is based on the wave modeling procedure and when i plot the graph for the...

05 June 2017 5,408 0 View

Evaluate the plastic shrinkage cracking of concrete?

Is there any kind of laboratory experiment set up to to evaluate the plastic shrinkage cracking of concrete by the rectangular shrinkage mould?

04 May 2017 4,805 7 View

Applicability of Blended cement and Polypropylene fiber (Or at least one) as a repair mortar to reduce chloride ion penetration in to concrete?

I need to know any research or any standard is available with regard to the Applicability of Blended cement and Polypropylene fiber (Or at least one) as a repair mortar for to reduce chloride ion...

01 January 1970 2,682 0 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Should I include H atom into C3N5 when i am doing DFT modelling?

Hi all, my experimental XPS results shown that my C3N5 sample consists of N-H bond, hence in this case I should incorporate the N-H bond into my DFT modelling. However, I do notice several papers...

07 August 2024 8,414 2 View

London dispersion in CCl4 vs the dipole-dipoles force strength in CHCl3?

How do you tie-break and rank these two in their strength?

03 August 2024 4,471 1 View

What are the limitations and challenges of using machine learning for predicting concrete compressive strength in practical applications?

Machine learning (ML) has shown great potential in predicting the compressive strength of concrete, an important property for structural engineering. However, its practical application comes with...

03 August 2024 2,546 2 View

Which statistical test should we use?

N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.

30 July 2024 7,233 4 View

How Can I Apply Hashin Damage Properties to Solid Elements in Abaqus Without Using VUMAT?

Sure, here is the translation: I have a 3D orthogonal woven composite structure where warp, weft, and binder yarns are oriented in three directions. After modeling these yarns and the matrix in...

28 July 2024 8,169 0 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Can you recommend provider Intermediate laboratory test for hydrocarbon, polyethylene & polypropylene?

Accredited laboratory of JV "Uz-Kor Gas Chemical" LLC (Uzbekistan) is looking for providers to conduct interlaboratory comparison tests on gas chromatographic analysis of hydrocarbons (component...

25 July 2024 8,108 0 View

Reason for discontinuities in my Band structure?

Hey All! I am wondering what might be wrong with my band structure. I did the calculations using VASP and plotted the results using Origin. Although I have tried changing various input...

25 July 2024 2,920 11 View